News:

SMF - installed December 2017.
Returning members - please use the 'Forgot Password' function when logging in to the new Forum for the first time. If you have changed your email address please let me know so I can update it.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - musicman

#1
Hi, I have a black oil pressure gauge from a 2 litre saloon. It does not have the oil pressure copper tube. let me know if you would like me to send it to you. My contact details are
leo.archibald@gmail.com
#2
I will check tomorrow to see if I have one in black.
#3
Do you mean the 2 litre drophead, if so black or beige coloured gauge.
#4
I plan to be there, I hope so as I am the organiser! Yes I am bringing my two Bucklands along with my Gold 2 Litre, I believe Mike Smith and Colin Naish are bringing their Bucklands, I hope many more 2 Litre and Bucklands will come to celebrate 75 years of the club. I look forward to meeting everyone. Best regards Leo
#5
I have seen this car before, it doesn't have the normal AC motif on the radiator cowl, just a badge. Also the frontal treatment of the car is very different. The front wings and radiator cowl are one piece, the cowl which is normally Brass could possibly be aluminium.  Normal Buckland's and 2 Litre Saloons have piping joining the panels. I have seen one other Buckland like this, is was a Maroon coloured car in very poor condition, I saw it back in the early 90's somewhere near the Liverpool area. I hope this info helps.
#6
Hi, I think you need to adjust the clutch pedal so as to give more clearance. The adjustment can be made under the car. You should be able to see a bracket attached to the bellhousing, you should be able to see how the adjustment should be made looking at the bracket as the clutch pedal is pressed down. Hope this info helps.
#7
I will try to send you an attachment. if this fails please give me your email address and I will forward a copy of the early wiring diagram.
Regards, Leo
#8
Ok, keep in touch and lets see what happens.
#9
Hello Fastpace, You have a very interesting project. I have available a completely  new rebuilt CL AC 2 litre engine which I now do not need, this might be of interest to you if you want to bring the car back to original. Let me know if you would like further details.
Leo
#10
Ace, Aceca & Greyhound Forum / Re: Gearbox help
August 27, 2021, 19:56:33
Hello Paul , I had the same problem many years ago, it was the clutch release bearing that had worn down, no matter what adjustments we made it came down to the bearing. I hope this helps
#11
Hello David, sadly I did not post the information re this Drophead, my code is not ARCH, but the photo is interesting as the car uses the same rear side window treatment as the one off drophead with the larger boot and petrol tanks in the front wings.
Regards
#12
Tom, did you receive my info on the updates I have found for the 2 Litre?
Regards, Leo
#13
Yes all the above details are correct. This D/H/C is chassis number ELX 1102, engine UMB 1103, as can be seen the car is left hand drive and was originally sent to Auto Palace in Holland.
#14
Hello, I read with interest your  problems with your carburetters. You mentioned that you have fuel misting at the entrance of the carbs. This normally happens when the valve timing is far advanced. For the vintage AC six the valve timing is inlet valve opens at 3.5 degrees after top dead centre and tappet clearance is .005 th.  Later engines have the inlet valve opening at 12 degrees before top dead centre and tappet clearance 20 th. It might be that if you adjust the timing chain sprocket one tooth it might help solve the fuel misting and the engine should run much smoother. These are only suggestions as I cannot know what way the engine has been set up re valve timing etc, but it's worth looking at to check all is well.
#15
Gary, I have looked at both cylinders small and larger bore, externally they are both the same size. The reason for the larger bore was because the rear brakes were changed to hydraulics thus the feeling was that a larger bore for pushing more fluid was required. However as you have fitted a servo and you are changing to hydraulic rear brakes, I would be inclined to try the system as it is and then make changes to the bore size afterwards. As I mentioned before the brake master cylinder is the same size, thus you could get the cylinder bored out and fitted with a new larger plunger and seal.
Hope this info helps. Regards Leo